詳細信息
通知：奧松機器人科技有限公司為Sparkfun官方中國區域代理，此款產品為國內首發，火熱搶購中，由于數量有限，拍下時請咨詢客服是否有庫存。
Arduino擴展板 Danger Shield for Arduino Sparkfun 原裝進口
此款Danger Shield for Arduino擴展板可以直接插到 Arduino或者是 Arduino Pro上使用，它配備有多種輸入輸出功能，對于剛剛?cè)腴TArduino的同學來說，Danger Shield for Arduino擴展板擁有無限潛力，您是不是已經迫不及待的想看到它在你的手中大放異彩了！
布線清晰 接口均有文字標注
產品特點：
1、產品名稱：Danger Shield for Arduino
2、產品貨號：RB-01C069
3、3個線性滑動電位計模塊連接到Arduino模擬引腳A0到A2
4、紅色和黃色的發光二極管連接數字引腳D5到D6（PWM引腳）可以更方便的更改其亮度
5、3個按鈕連接Arduino數字引腳D10到D12。按下按鈕時線會變低
6、光電管和溫度傳感器都可模擬輸出，分別連接模擬引腳A3和A4
7、由一個8位移位寄存器來控制一個藍色的7段數碼管
8、蜂鳴器可以由你的Arduino中獲得聲音
9、電容式觸摸板則是通過電容感應庫感應觸摸
尺寸標注清晰 sparkfun進口LOGO醒目
發貨清單：
- 1xPCB擴展板
- 3x滑動電位計 - 10K
- 1x7段LED - 藍
- 1x8位移位寄存器 - 74HC595
- 1x溫度傳感器 - TMP36
- 1x光敏電阻
- 1x蜂鳴器
- 1x發光二極管-紅色
- 2x發光二極管-黃色
- 1x按鈕
- 3x瞬時開關按鈕 - 12毫米廣場
- 11x電阻器 - 330歐姆
- 1x電阻器 - 10K歐姆
- 1x電阻1M歐姆1/6W
- 2x8針的Arduino DIP插頭
- 2x6針的Arduino DIP插頭
注意：該產品均為散件，附帶配件需自行焊接到PCB板上。
精致發光二極管及其他電阻
產品配件清晰 方便焊接
Description:
The Danger Shield mounts on top of your Arduino or Arduino Pro and equips it with a variety of fun and useful inputs and outputs. The Danger Shield has so much potential; we can\'t wait to see what you\'re able to do with it! The shield\'s features include:
- Three linear slide potentiometers connected to the Arduino\'s analog pins 0 through 2.
- Red and yellow LEDs connected to digital pins 5 and 6 - PWM pins - so you can easily vary their brightness.
- Three momentary push buttons connected up to the Arduino\'s digital pins 10 through 12. Those lines will go low when the buttons are pressed.
- A photocell and a temperature sensor, both with analog outputs, are connected to the analog pins 3 and 4, respectively.
- An 8-bit shift register set up to control a blue 7-segment LED.
- A buzzer - so you can get sound out of your Arduino
- Capacitive Touch pad - Using the CapSense library to sense touch.
This product comes as a kit of parts, which you\'ll have to solder into the included PCB. All parts are through-hole so it should go together relatively easily; but always check your component orientation before soldering!
Kit Includes:
- 1x PCB Danger Shield Kit
- 3x Slide Potentiometers - 10K
- 1x 7-Segment LED - Blue
- 1x 8-bit Shift Register - 74HC595
- 1x Temperature Sensor - TMP36
- 1x Miniature Photocell
- 1x Buzzer
- 1x Basic LED - Red
- 2x Basic LEDs - Yellow
- 1x Mini Push Button
- 3x Momentary Push Buttons - 12mm Square
- 11x Resistors - 330 Ohm
- 1x Resistors - 10K Ohm
- 1x Resistor 1M Ohm 1/6W
- 2x 8-pin Arduino Stackable Headers
- 2x 6-pin Arduino Stackable Headers
產品應用圖片展示
相關下載文件（復制鏈接到瀏覽器）：
1、Schematic
http://dlnmh9ip6v2uc.cloudfront.net/datasheets/Dev/Arduino/Shields/Danger_Shield-v17.pdf
2、Eagle Files
http://dlnmh9ip6v2uc.cloudfront.net/datasheets/Dev/Arduino/Shields/Danger_Shield-v17.zip
3、Example Code
http://dlnmh9ip6v2uc.cloudfront.net/datasheets/Dev/Arduino/Shields/Danger_shield_V16_CapSense.zip
4、GitHub
https://github.com/sparkfun/DangerShield