国产精品成人一区二区三区-精品久久久久久久免费人妻-亚洲色精品aⅴ一区区三区-国产在线aaa片一区二区99

參數資料
型號： XBIB-U
廠商： Digi International/Maxstream
文件頁數： 13/72頁
文件大小： 1116K
描述： BOARD USB ZIGBEE MOD PRO
設計資源： XBIB-U Shematic
標準包裝： 1
附件類型： 接口板
適用于相關產品： XBee 和 XBee Pro 收音機
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?3
Chapter??燫F燤odule燨peration
2.2.2. API Support
I/O data is sent out the UART using an API frame. All other data can be sent and received using
Transparent Operation [refer to p10] or API framing if API mode is enabled (AP > 0).
API Operations support two RX (Receive) frame identifiers for I/O data:
" 0x82 for RX (Receive) Packet: 64-bit address I/O
" 0x83 for RX (Receive) Packet: 16-bit address I/O
The API command header is the same as shown in the RX (Receive) Packet: 64-bit Address and
RX (Receive) Packet: 64-bit Address API types [refer to p58]. RX data follows the format
described in the I/O Data Format section [p12].
Applicable Commands: AP (API Enable)
2.2.3. Sleep Support
When an RF module wakes, it will always do a sample based on any active ADC or DIO lines. This
allows sampling based on the sleep cycle whether it be Cyclic Sleep (SM parameter = 4 or 5) or Pin
Sleep (SM = 1 or 2). To gather more samples when awake, set the IR (Sample Rate) parameter.
For Cyclic Sleep modes: If the IR parameter is set, the module will stay awake until the IT (Sam-
ples before TX) parameter is met. The module will stay awake for ST (Time before Sleep) time.
Applicable Commands: IR (Sample Rate), IT (Samples before TX), SM (Sleep Mode), IC (DIO 
Change Detect)
2.2.4. DIO Pin Change Detect
When DIO Change Detect is enabled (using the IC command), DIO lines 0-7 are monitored.
When a change is detected on a DIO line, the following will occur:
Note: Change detect will not affect Pin Sleep wake-up. The D8 pin (DTR/Sleep_RQ/DI8) is the only
line that will wake a module from Pin Sleep. If not all samples are collected, the module will still
enter Sleep Mode after a change detect packet is sent.
Applicable Commands: IC (DIO Change Detect), IT (Samples before TX)
NOTE: Change detect is only supported when the Dx (DIOx Configuration) parameter equals 3,4 or 5.
2.2.5. Sample Rate (Interval)
The Sample Rate (Interval) feature allows enabled ADC and DIO pins to be read periodically on
modules that are not configured to operate in Sleep Mode. When one of the Sleep Modes is
enabled and the IR (Sample Rate) parameter set, the module will stay awake until IT (Samples
before TX) samples have been collected.
Once a particular pin is enabled, the appropriate sample rate must be chosen. The maximum sam-
ple rate that can be achieved while using one A/D line is 1 sample/ms or 1 KHz (Note that the
modem will not be able to keep up with transmission when IR & IT are equal to 1).
Applicable Commands: IR (Sample Rate), IT (Samples before TX), SM (Sleep Mode)
1.   An RF packet is sent with the updated DIO pin levels. This packet will not contain any ADC
samples.
2.   Any queued samples are transmitted before the change detect data. This may result in
receiving a packet with less than IT (Samples before TX) samples.
相關PDF資料
PDF描述
XIB-E BOARD INTERFACE ETHERNET
XIB-R BOARD INTERFACE RS232/485
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
相關代理商/技術參數
參數描述
XBIB-U-DEV 功能描述:界面開發工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBIB-U-SP 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBIB-U-SS 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBL6450BYFVR 制造商:Texas Instruments 功能描述:ECS BLUELINK - Tape and Reel
XBL6450YFHR 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*